Volume 2, Issue 6, November 2017, Page: 83-102
Finite Element Simulation of Deep Drawing of Aluminium Alloy Sheets
Shaik Himam Saheb, Department of Mechanical Engineering, ICFAI University, Hyderabad, India
M. Sree Hari, Department of Mechanical Engineering, Gurunanak Institutions, Hyderabad, India
Annam Vijay Kumar, Department of Mechanical Engineering, Gurunanak Institutions, Hyderabad, India
Received: Oct. 5, 2017;       Accepted: Nov. 1, 2017;       Published: Jan. 16, 2018
DOI: 10.11648/j.ijimse.20170206.13      View  1352      Downloads  98
Abstract
More and more automobile companies are going for weight reduction of their vehicles for fuel economy and pollution control. The objective of the present study is to determine the effect of blank temperature on forming behaviour of sheets and damage factor of aluminium sheet alloys of 6061 and 7075 at elevated temperatures. Although the aluminium alloys have high-strength to weight ratio and good corrosion resistance, the low formability of aluminium sheets limits their use in some products with complex shapes, such as automotive body parts. The elevated forming process is intended to overcome this problem. An insight into such a study will throw light on the different temperatures required by the above materials when they are made into TWBs. Using ANSYS a series of simulations were carried out in the present investigation on the formability behaviour of deep drawing of aluminium alloys in the temperature range 200-500°C.
Keywords
Aluminium Alloys, Forming, Damage Factor, ANSYS
To cite this article
Shaik Himam Saheb, M. Sree Hari, Annam Vijay Kumar, Finite Element Simulation of Deep Drawing of Aluminium Alloy Sheets, International Journal of Industrial and Manufacturing Systems Engineering. Vol. 2, No. 6, 2017, pp. 83-102. doi: 10.11648/j.ijimse.20170206.13
Copyright
Copyright © 2017 Authors retain the copyright of this article.
This article is an open access article distributed under the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/) which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Reference
[1]
D. M. Finch, S. P. Wilson, J. E. Dorn. 1946. Deep drawing aluminium alloys at elevated temperatures. ASM Trans. 36: 254-289.
[2]
S. Fulki. 1984. Deep drawing at elevated temperatures. Rep. Inst. Phys. Chem. Res. 24: 209-211.
[3]
M. Miyagawa. 1959. Deep drawing methods at elevated temperatures. J. JSME. 62: 713-721.
[4]
Y. Tozwa. 1960. Deep drawing methods by circumferential heating. J. Jpn. Soc. Tech. Plasticity. 1: 23-28.
[5]
Y. T Keum, B. Y. Ghoo, R. H. Wagoner. 2001. 3 dimensional finite element analyses of non isothermalforming processes for non ferrous sheets. K. Mori (Ed). Simulation of Materials processing: Theory, Methods and applications. A. A. Balkema. Lisse. pp. 813-818.
[6]
R. Neugebauer, T. Altan, M. Geiger, M. Kleiner, A. Sterzing. 2006. Sheet Metal Forming at Elevated Temperatures. Annals of the CIRP. Vol. 55/2.
[7]
Srihari, M & Shaik, Himam & Vijaya Nirmala, S. (2016). Design And Analysis Of Crankshaft For 4-Stroke Deisel Engine. International Journal of Scientific Research and Modern Education (IJSRME). 1. 10.5281/ZENODO.158931.
[8]
J Bagde, Bhumesh & Raut, Laukik. (2013). FINITE ELEMENT ANALYSIS OF SINGLE CYLINDER ENGINE CRANK SHAFT. 6. 2231-1963.
[9]
Shaik, Himam & Reddy, Govardhana & Hameed, Md. (2016). DESIGN REPORT OF A GO KART VEHICLE. International Journal of Engineering Applied Sciences and Technology, 2016. 1
[10]
Serkan Toros, Fahrettin Ozturk, Ilyas Kacar. 2008. Review of warm forming of aluminum-magnesium alloys. Journal of materials processing technology. 207: 1-12.
[11]
Shehata FA. 1986. Tensile behaviour of aluminium/magnesium alloy sheets at elevate temperatures. Sheet Met Indus. 63 (2): 79-81.
[12]
S. Mahabunphachai, M. Koç. 2010. Investigations on forming of aluminum 5052 and 6061 sheet alloys at warm temperatures. Materials and Design. 31: 2422-2434.
Browse journals by subject